您当前的位置:首页>论文资料>可变喷油速率的超高压共轨系统喷射控制研究

可变喷油速率的超高压共轨系统喷射控制研究

资料类别:论文资料

文档格式:PDF电子版

文件大小:1.7 MB

资料语言:中文

更新时间:2025-01-13 14:10:42



推荐标签:

内容简介

可变喷油速率的超高压共轨系统喷射控制研究 第38卷第3期 2017年6月
内燃机工程
Chinese Internal Combustion Engine Engineering
文章编号:1000—0925(2017)03—0068—06
杨昆,欧阳光耀,常远,刘振明
(海军工程大学动力工程学院,武汉430033)
Vol. 38 No. 3 June. 2017
380055
Research on Injection Control of Ultra High Pressure Common Rail System with
Variable Fuel Injection Rate
YANGKun,OUYANGGuangyao,CHANGYuan,LIUZhenming
(Academy of Power Engineering, Naval University of Engineering, Wuhan 430033, China)
Abstract: A simulation model of ultra high pressure common rail system with variable fuel injection rate was established by AMESim software, and the characteristics of the fuel injection rate under same injection quantity were analyzed. Using the combustion model of a single cylinder diesel engine built by GT Power software, the different fuel injection rate was inputted into the engine model to research the effect of different fuel injection rates on cylinder pressure, cylinder temperature, heat release rate, exhaust emissions, torque and fuel consumption. Simulation results show that the comprehensive performance of the engine can be optimized by matching a saddle-shaped injection rate with an appropriate fuel injection timing- At the same time, the injection control experiment with different fuel injection rate was carried out on a test bench. Experimental results show that: compared with the same fuel quantity of high pressure common rail injection, the ultra high pressure fuel injection with variable injection rate can be used for diesel engine to obtain more excellent power performance and fuel economy. This will make the power output increased by 5% and the fuel consumption decreased by 6% with higher NO, emissions and lower soot emissions. The research conclusions can help to explore the fuel injection law, thus improving the engine performance.
摘要:通过AMESim软件建立了喷油速率可调的超高压共轨系统仿真模型,分析了相同喷油量条件下喷油率的变化特点。采用GT-Power软件建立单缸荣油机模型,将不同喷油率导入案油机的燃烧计算模型,研完了不同喷油率对柴油机缸内压力、缸内温度、放热率、NO 排放、碳烟排放及输出转矩和油耗率的影响。仿真结果表明:靴形喷油速率匹配合适的喷油提前角可优化荣油机的综合性能。搭建了超高压共轨荣油机台架,开展了不同喷油速率的喷射控制试验,结果表明:与相同油量条件下的高压共轨喷射相比,荣油机实施变喷油速率超高压喷射可获得更优异的动力性和燃油经济性,动力输出提高了5%,燃油消耗量下降了6%,碳烟排放降低,但NO,排放升高。
关键词:柴油机:超高压共轨系统;变喷油速率;喷射控制
Key words: diesel engine; ultra high pressure common rail system; variable
injection rate; injection control
DOI: 10. 13949/j. cnki. nrjgc. 2017. 03. 011
中图分类号:TK421
收稿日期:2015-08-27
文赋标识码:A
基金项目:国家自然科学基金项目(51379212);国家自然科学基全项目(51409254):海军工程大学白然科学基金项目(HGDYDJJ13005)
昆(1981—),男,副教授,主要研充方向为动力机械及热力系统的设计、伤真与优化,E-mail:150006224@qq.com
作者简介:杨万方数据
上一章:某小型汽油机功率提升的试验研究 下一章:某柴油机曲轴箱通风系统优化研究

相关文章

柴油机高压共轨喷油系统设计优化及智能控制 高压共轨柴油机喷射系统参数优化方法研究 高压共轨缝隙式喷油器喷雾特性的仿真研究 高压共轨柴油机蓄压式喷油器喷嘴内流特性研究 高压共轨大功率柴油机喷油嘴内部两相流动仿真研究 超高压共轨系统轨压控制策略研究 高压共轨喷油器驱动电路的优化设计 GB/T 25368-2010 柴油机电控共轨喷油系统高压供油泵总成 技术条件